LD90 - 3
General Information
The sensors of series LD90-3 are based upon the well-proved principle of time-of-flight measurement of short laser pulses, like all RIEGL products.
They can be operated with practically any target surface, i.e. "reflectorless" up to many hundred meters, and with reflecting foil or retroreflectors up to more than 1000 m.
LD 90-3 LD90-3 with RS232 / RS422 data interface, connection cable, and user's manual
Options
- Analog current output 4-20 mA, not galvanically isolated.
- Transistor switching outputs 2x PNP (not available for all instrument types)
- Speed Measurement Firmware implemented (for LD90-3200HiP only)
- Configuration, Control & Communication software License LaserWin 4 (runs under WINDOWS NT, 2000, and XP platforms)
- LaserWin 4 - SPEED IPU License, extends LaserWin by an additional speed calculating module
- For EHS-instruments only: Driver License RiPORT for operating systems WINDOWS NT, 2000, and XP platforms for data acquisition via ECP Port on PC platform, with source code examples for interfacing to Microsoft Visual C++.
Scanner Accessories
Special Housings
* This is a component only intended for incorporation in „apparatus" by professional manufacturers. It must not be placed on the market for distribution and/or final use. Therefore, the provisions of the EMC Directive 89/336/EEC such as CE-marking or EC declaration of conformity are not mandatory and, therefore, not applied. The manufacturer of the end apparatus has, under his responsibility, to comply with the EMC directive as far as applicable".
1. Protection case IP66, 200 x 300 x 120 mm, painted steel, with sealed front window assembly, with internal mount for the LD90-3 distance sensor, and with cable glands for DC power supply and data interface
2. Lens protection tube, with fittings for pressed air purging, detachable for cleaning the front glass
3. Shock-absorbing mount
4. Pan & Tilt adjustment mount, ± 20 degrees both axes
5a.
Red semiconductor laser beampointer with mount
5b. Telescope 3x20 with mount
6. Internal heater for the front window and the electronics.
Aiming Devices
Telescope 3x20 (detachable) for LD90-3800EHS-FLP and for LD90-3800VHS-FLP only!
Telescope 3x20 with mount for the LD90-3 case, coaligned with the measuring beam
Telescope 1.5-4x16 with mount for the LD90-3 case, coaligned with the measuring beam. Red semiconductor-laser beampointer, coaligned with the measuring beam
Mounting
Pan & Tilt adjustable mounting base for LD90-3
Pan & Tilt shock-absorbing adjustable mounting base for LD90-3
Shock-absorbing mount for LD90-3
Lens protection tube
Mounting flange assembly comes with:
- Mounting flange made of stainless steel, thickness approx. 2 mm,
nominal width 150 mm, outer diameter 285 mm, 8 holes for mounting
(diameter 22 mm), hole circle diameter 240 mm - Lens portection tube, length approx. 400 mm with air flow directing
sheets and integrated fittings for pressed air or nitrogen flushing - Mounting plate for LD90-3
- Seal and fastening screws
Cables
CE-conform, shielded connection cable, length 3 m
CE-conform, shielded RS232 data cable, length 3 m
Peripheral Equipment
External power supply module VNG95, 100 - 240 V AC / 0.8 A / 47 - 63 Hz
Remote LED data display RD95, 6 digits
Retroreflecting Targets
Plastic reflection foil, approx. 0.25 m2 (46 cm x 46 cm)
Plastic reflector, 84 mm diameter
Glass retroreflector-prism, 60 mm diameter
Mount for glass retroreflector-prism
Our distance meters use the time-of-flight method to determin the distacne of a remote target by measuring the transit time between transmission and reception of a shorter laser pulse.
Get the Specs
View the technical specifications for our terrestrial scanners. Select a model from the list below:
© 2008 Riegl USA. All Rights Reserved.